No, it was more recently in one of the TH build threads over on AVS, but I couldn't find it in a quick search. Regardless, most folks over there use REW with good results.Quote:
Originally Posted by Earl K
GM
Printable View
No, it was more recently in one of the TH build threads over on AVS, but I couldn't find it in a quick search. Regardless, most folks over there use REW with good results.Quote:
Originally Posted by Earl K
GM
Hey Earl it's not the built in mic I have it disabled here's my sound control panel.Looks like I have some work to do.Great just what I need more work as if I don't have enough already. :(Quote:
Originally Posted by Earl K
http://www.hostboard.com/forums/hbmc.../2010/10/2.png
John, show me a screen shot your control panel ( mixer ) for the soundcards' driver software .
FYI, I find M-Audios control panels somewhat less intuitive than they ought to be .
It's really easy to make a mistake within that mixer/monitor panel ( IME ) .
<> cheers
First thing I did was dug out an old amp I have, it is just 25 wpc built in the mid '70's when they were still built like tanks 35 years old and never had to replace a thing on it,bulbs still work.:) And I'm going to use that for my dedicated measuring amp.And I went through the steps of re-setting up the test gear.And I noticed an imediate improvement.I remeasured.Does this look better.;)
This little dinky thing.:eek:
http://www.hostboard.com/forums/hbmc...2010/10/40.jpg
http://www.hostboard.com/forums/hbmc...2010/10/41.jpg
http://www.hostboard.com/forums/hbmc...2010/10/40.jpgQuote:
This little dinky thing ?:eek:
Yes, that's what I'm referring to .
Are those selections all greyed-out because you are unable to change them ?
Or are they changeable ?
- To see if they are changeable ( close down Holm & this panel ) then open up just the Fast TRack Pro sound panel .
- If the choices are now changeable , // deselect the " Balanced input 1 ( mono ) " choice // then close this M-Audio panel / / & then fireup Holm and try to measure something .
- Ie ; if you still have mic input into Holm / then that means the selection in question is actually a monitoring input ( feeding both outputs ) and is therefore feeding back into your results ( not good, since it'll contaminate the results ! ) .
<. cheers
No they are changeable once stream is active they grey out don't know why ? but before I active i can change inputs/outputs.Quote:
Originally Posted by Earl K
Ok will give it a whirl Thanks Earl !! (No Pun intended) :D Back in a minute :2thumbsup:
ADDED: No Earl no sound is picked up through the Mic here's the message from Holm.But a funny thing happened when I was uploading captures to photobucket one of those animation ads came on Photobucket i heard a click sound and then the ads sound started playing through the 288/511 that I was measuring.
http://www.hostboard.com/forums/hbmc...2010/10/42.jpg
The reason is ;Quote:
Originally Posted by John
- Once data streaming is implemented by Holm / only Holm has "control" of that sound panel ( obviously, Holm must be open to have ownership/control ) .
<> cheers
So what next Earl did you take a look at the graphs,the new measurement of the 288 w/299 fram driver #2 ?
I'm going to re-measure the first 288's I measured.I have them on my 1005's now though to see if they are similar or consistant.
I suggest that you run a sweep with no input (as per my email). Disconnect the mic. If the no input sweep does not return a straight line way down the scale, then something is amiss. Alos turn off outputs 3&4 if you are not using them.
We may need to recalibrate your card if things still look odd.
I will follow your instructions (per email) Pano and will send a reply after completion Thanks Again !!! :2thumbsup:Quote:
Originally Posted by Panomaniac